FLURRY GATEFOLD

The following blog post was published as a Guest Post on The Crafty Blog Stalker on November 19.

The tutorial for making the card is very detailed and filled with photos. Follow along if you would like to. I would be most pleased if you would! The card I will be showing you how to create is this one:

Because the card doesn't open traditionally -- right to left or bottom to top -- but from the center point, it is referred to as a gatefold card. 

To get the folds in the exact spot, start with a piece of cardstock that measures 5 1/2" x 8 1/2". Place the 8 1/2" edge up against the top of the Simply Scored, and score at 2 1/8" and 6 3/8".

Crease on these score lines with a bone folder so the card stays shut just right.

From Whisper White cardstock, cut two pieces that measure 1 7/8" x 5 1/4". I just have them lying in place on my card to illustrate.

Now, comes a really fun part -- a little thing that I like to do in my papercrafting as often as inspiration strikes me! -- when you use something that isn't normally considered a crafting supply. For this card, I was inspired by the plastic mesh bag in which my oranges arrived. Look at something "odd" with a different eye. In this case, I immediately saw this mesh as a STENCIL!

Cut off a piece of this mesh that is larger than your two white panels. Grab a Stamping Sponge and an ink pad and go to work! Because in my mind, snow flurries are not even in the way they appear, I echoed that in my sponging. So I varied the pressure I used in my stencil sponging so some spots were lighter, while others were darker, giving the panels a nice variety of color intensities.

Once I had both panels sponged to my taste, I glued them in place on the gatefolds of the card.

Instead of decorating this part of the card any further, I decided to opt for creating a belly band for the decorative part. Belly bands are fun and easy to create, and they can look so impressive!

A multi-layered snowflake was my choice for embellishment for the belly band for this card. I proceeded to make each of the three layers slightly different. I used three of the snowflakes from the Festive Flurry set. The bottom layer was stamped first in VersaMark on Lost Lagoon cardstock, then heat embossed in silver. My second layer was simply stamped in Lost Lagoon ink on Whisper White cardstock, while the smallest snowflake was embossed in silver on Whisper White.

I used the matching Framelits to cut out the snowflakes precisely. The blue on white snowflake is still inside its Framelit.

To make my very dimensional snowflake, I used Stampin' Dimensionals between each layer as I popped them together.

As a finishing touch, I added a Basic Rhinestone to the center. Just the PERFECT amount of bling. 

To create the belly band itself, cut a strip of Whisper White cardstock measuring 1" x 8 1/2". Lay the card centered on top of the strip, and carefully bend the ends up so they almost meet in the center. (No problem that they don't meet; the tiny gap will be covered by the elegant snowflake.)

Crease those folds well with a bone folder so the belly band will fit snugly and look neat.

Rub an Embossing Buddy over the strip with the folds facing upwards. Then, with the spotty stamp from Gorgeous Grunge, stamp several times across this strip in VersaMark. 

Cover your VersaMark spots with White Embossing Powder, tapping the excess powder back into its container. Heat emboss until all the powder is melted.

Grab your Stamping Sponge again, and gently cover those spots with Lost Lagoon ink. This technique is called a resist, in that wherever you have embossing, those spots will "resist" the ink, and remain white. Once you have the intensity of ink sponged on that you desire, you are set to move on.

Take a piece of Lost Lagoon ribbon that is about 9 1/2" long. Add Glue Dots here and there, and adhere the ribbon to the center of the resist strip, securing the ends of the ribbon onto the back of the belly band with tape.

Add some glue to the back of the snowflake and adhere the snowflake to the closed belly band. Once the glue has set, you can slide it into place on your card.

Wait!! We're not quite finished yet!

We are going to repeat some of that resist technique inside the card. Remember that the inside is Lost Lagoon? Cut a piece of Whisper White cardstock that measures 4" x 5 1/4". Repeat the same embossing steps you did on the dotted belly band: Rub the Embossing Buddy well over the cardstock, followed by your stamping in VersaMark whatever sentiment you have chosen. Cover this with White Embossing Powder and heat it until the entire stamped image is shiny.

Gently sponge Lost Lagoon ink over the embossed portion. Remember to start out softly; you can always add to the intensity of the ink. But, once you have it too dark, there is no going back. Keep the ink the darkest over the sentiment so it is readily legible, feathering it off into the distance.

Glue this panel inside the card for a neat finish that echoes the work you have done on the belly band.

And, here is your finished product. Lots of steps, a little bit of time, but well worth it, don't you agree?

 I simply adore the very dimensionl look of the snowflake on the belly band.

To open the card, your recipient merely slides the belly band off.

And this is what they will find inside to greet them!

I would love it if you would join me: Paper Seedlings, Instagram, Facebook, Pinterest, Twitter.

Flurry

Smiles.